Peristaltic Pump and Pump Motor - Discontinued

FPU500 FPU5MT

Peristaltic Pump and Pump Motor

OMEGAFLEX™ PERISTALTIC PUMP
Stainless Steel Rotor Assembly
Ideal for Use in Sterile, Corrosive, or General Operating Environments
Flowrates from 1.0 to 2280 mL/Min (36 GPH)
Mounts Directly onto OMEGAFLEX ® Motor or Compatible Pump Motor
Easily Stackable Mounting for Multichannel Pumping
Three-Roller Geometry Reduces Pulsation and Improves Priming
Polysulfone Housing for Durability and Chemical Resistance
FPU5-MT PUMP MOTOR
Digital Display of Flowrate, RPM, Total Volume, Fluid Temperature (°F or °C), Flow Duration, or Tube ID
Flow Rate 1.0 to 2280 mL/Min (10 to 600 RPM) Reversible
Easy-to-Read Display
Type K SMP Female Thermocouple Input
Tachometer Feedback, ±0.5% Speed Control
Accepts Two Pumps, One on Each Side or Two Stacked Together
Membrane Keypad for Easy Calibration
Remote Control Options Aux. In: Remote Start/Stop Aux. Out: Remote Monitor
Built-In Electronic Braking and Reversing for Fast Stops and Directional Changes
Accepts Metric or English Tube Sizes
Displays Information in English, French, Spanish, German, or Italian

Description

The FPU500 FPU5MT series has been discontinued. Please see the FPU2000A as a possible alternative or contact our Flow Engineering department.

The FPU500 Series peristaltic pumps from OMEGA offer exceptional simplicity, ease of use, and variable flow capability. A motor turns the pump’s rollers, which squeeze fluid through precision-bore tubing in a wavelike motion. The fluid does not come into contact with the pump; only the outside wall of the tubing does. This makes these pumps ideal for use in sterile, corrosive, or general fluid flow operating environments.

The pump is self-priming and non-siphoning. When one section of the tube fatigues, simply move the tube along to an unused section and continue pumping. No tools are required to load the tube. A precision-molded tubing cavity provides the proper occlusion for the recommended tubing. A tube clamp holds the tubing securely in place. Tubing is easily changed without removing the pump.

One pump can be used for many different applications, or you can mount two pumps onto the motor. The pumps work with a wide variety of OMEGAFLEX™ plastic tubing. Vinyl, FKM, Tygon, silicone, Santoprene, and Norprene® tubing can be purchased in a broad range of sizes. The standard rotor assembly is made of stainless steel.

The FPU500 pump can be purchased with an optional adaptor plate that can be used to mount the pump to a motor other than the FPU5-MT pump motor. The pump comes standard with 2 short mounting screws, used to mount one pump at a time. If you need to stack two pumps, order long mounting screws.

SPECIFICATIONS
Maximum Back Pressure: 20 psi
Maximum RPM to Prime: 100 RPM
Tube Wall: 1.6 mm (¹⁄16")
Fluid Temperature Range: -46 to 149°C (-50 to 300°F)
Dimensions, Pump: 102 H x 102 W x 57 mm D (4 x 4 x 2¼")
Optional Mounting Plate: 76 H x 64 W x 3.2 mm D (3 x 2½ x ¹⁄8")
Weight, Pump: 408 g (14.4 oz)
Optional Mounting Plate: 91 g (32 oz)
Maximum Tubing Size: 8 mm (⁵⁄16")
Maximum Tube Durometer: 65 Shore A

The OMEGAFLEXR FPU5-MT pump motor offers microprocessor control and a digital display, and is designed to be fully compatible with OMEGA's FPU500 pump. No mounting plate is needed, just two mounting screws. A ¹⁄10 HP (75 W) motor provides flow rates of up to 2280 mL/minute. The user enters values and controls all operations through a convenient membrane keypad. A dot matrix LCD provides for easy viewing. Calibrating the unit is easy with the user-friendly control software. Simply select a tubing size and the desired flow rate, and the pump motor locks in the required RPM. Select nominal calibration values stored in ROM (read only memory) or calibrate via gravimetric or flowmeter measurements. Fluid temperature may be displayed (using an optional thermocouple probe). The last flow settings are stored in memory when the drives are shut off.

SPECIFICATIONS
Motor: Reversible, ¹⁄10 HP (75 W), 90 Vdc
Display: 16-character dot matrix LCD, 9 mm H (³⁄8") characters
Power: 90 to 130 Vac, 1.5 A; 190 to 260 Vac, 0.8 A
Line Cord: 1.8 m (6') with U.S. standard plug on 115 Vac units; European plug on 230 Vac units
Housing: Painted sheet metal with rubber feet; units are stackable
Dimensions: 152 H x 254 W x 254 mm D (6 x 10 x 10")
Weight: 8.2 kg (18 lb)

Place Order(Specify Model Number)

What Other People Bought: When you see this icon, click on it to expand a list of products that other people have bought when they purchased this model.

Part Number/ Desc.

Qty

Description

FPU500

Consult Sales

Availability:

Peristaltic Pump Head

FPU5-MT-110

Consult Sales

Availability:

110 Vac Pump Motor

FPU5-MT-220

Consult Sales

Availability:

220 Vac Pump Motor

Accessories

FPU500-AP

Consult Sales

Availability:

Adapter plate

FPU500-LMS

AUD17.46

Availability: 1 week

Long mounting screws (2)

FPU500-SMS

AUD17.46

Availability: 1 week

Short mounting screws (2)

FPU500-RA

Consult Sales

Availability:

Replacement rotor assembly

† All amounts shown in AUD
Note: The FPU500 pump can be purchased with an optional adaptor plate that can be used to mount the pump to a motor other than the FPU5-MT pump motor. The pump comes standard with 2 short mounting screws, used to mount one pump at a time. If you need to stack two pumps, order long mounting screws.