SCR Power Controllers for Electrical Heaters Control

SCR19 and SCR39 Series

^AUD692.42 SCR19Z-24-040

PLACE ORDER

SCR19 SCR Power Controllers Extend Heater Life Reducing Thermal Shocks
Zero Crossing or Phase Angle Fired
Single or Three Phase Load Switching
No Maintenance All Solid State Components
Close Control of Low Mass Heaters
Phase Angle with Soft Start for High Inrush Heaters
No Relay Noise Contact Arc Noise Eliminated
Semiconductor I2T Fusing
Optically Isolated Control Signal Input

Temperature and Process Controllers and Power Switching Devices - View related products

Description

The SCR19 Series SCR Power Controllers are designed to proportion electric power to resistive loads only, such as ovens, furnaces, heat sealers, etc. (NOTE: They are not designed to drive transformers or any inductive load.)

These heater controllers consist of power semi-conductors (SCRs), properly-sized heat sinks, trigger circuitry, and fuses supplied on panels for surface mounting. The SCR power controller accepts a 4 to 20 mA dc output from a temperature controller or can be supplied with manual option using a remote potentiometer.

The SCR19 Series controllers offers two methods of proportional control – Zero-voltage-switched and Phase-angled-fired. With the Zero-voltage-switching mode, the controller switches on complete cycles of the ac supply voltage. The trigger circuit is designed to turn on the SCRs as close as possible to the point where the AC sine wave crosses through zero. In effect, the line voltage is turned on and off and applied to the heaters in whole cycles.

With an input of 4 to 20 mA, the output of the heter controller will be off below 4 mA and full on at 20 mA. Proportioning action is obtained by varying the number of cycles on to the number of cycles off. The output will vary from one cycle on and nine cycles off at low input, to all cycles on at maximum input.

The output of the SCR19 SCR power controllers is integrated by the heaters which produce a smoothly proportioning heat output that varies directly with the input signal. With the Phase-angle-fired mode, the power to the load is controlled by governing the point of turn on (firing) of each half cycle of the full AC sine wave.

Place Order(Specify Model Number)

What Other People Bought: When you see this icon, click on it to expand a list of products that other people have bought when they purchased this model.

Part Number/ Desc.

Qty

Description

SCR19Z-12-040

AUD705.00

Availability: 1 week

SCR power controller, Zero-Voltage-Switching, 120V, 40A

SCR19Z-24-040

AUD692.42

Availability: 1 week

SCR power controller, Zero-Voltage-Switching, 240V, 40A

SCR19Z-48-040

AUD726.76

Availability: 1 week

SCR power controller, Zero-Voltage-Switching, 480V, 40A

SCR19Z-24-060

AUD655.00

Availability: 1 week

SCR power controller, Zero-Voltage-Switching, 240V, 60A

SCR39Z-24-060

AUD1,345.00

Availability: 10 weeks

SCR power controller, 3-phase, Zero-Voltage-Switching, 240V, 60A

SCR39Z-48-060

AUD1,430.00

Availability: 1 week

SCR power controller, 3-phase, Zero-Voltage-Switching, 480V, 60A

SCR19P-24-040-S15

AUD845.00

Availability: 1 week

SCR power controller, Phase-Angle-Switching, 240V, 40A, 15 sec soft start circuit

SCR19P-24-080-S9

AUD895.00

Availability: 10 weeks

SCR power controller, Phase-Angle-Switching, 240V, 80A, 9 sec soft start circuit

Accessories

SCR-210A015U01

AUD163.00

Availability: 1 week

Replacement Fuse, 40 A

SCR-210A012U01

AUD195.00

Availability: 1 week

Replacement Fuse, 60 A

SCR-210A014U01

AUD181.00

Availability: 1 week

Replacement Fuse, 80 A

SCR19Z-M

AUD226.00

Availability: 10 weeks

Manual remote pot for 120V SCR19/39 models

SCR19Z-M-220

AUD226.00

Availability: 10 weeks

Manual remote pot for 240V SCR19/39 models

SCR19Z-M-480

Consult Sales

Availability:

Manual remote pot for 480V SCR19/39 models

Order By Part Number

Part Number

Qty

Part Number

Qty

† All amounts shown in AUD
Note: Comes with complete operator’s manual
Ordering Example: (1) SCR19Z-24-040 SCR, Zero-Voltage-Switching, 240V, 40A, AUD692.42

Part Number Builder

Build Your Part Number Below

	(1)		(2)	(3)	(4)	(5)
SCR		9

Option Descriptions:

(1) Single or 3 Phase select from:
1 for Single Phase
3 for 3 Phase

(2) Method select from:
Z for Zero-Voltage Switching
P for Phase-Angle Firing

(3) Voltage select from:
-02 for 24 Vac for single phase only
-12 for 120 Vac for single phase only
-20 for 208 Vac for phase angle firing
-24 for 240 Vac
-48 for 480 Vac

(4) Current select from:
-040 for 40 Amps
-060 for 60 Amps
-080 for 80 Amps

(5) Phase-Angle Firing Items select from:
for Zero-Voltage Switching leave field blank
-S9 for the STANDARD Soft start 9 seconds
-S15 for Soft start 15 seconds
-S30 for Soft start 30 seconds
-S60 for Soft start 60 seconds
-S120 for Soft start 120 seconds
-V for Voltage limit

Note: All combinations may not be valid, check spec sheet for valid part numbers.